PICkit 3 In-Circuit Debugger/Programmer

PICkit 3 In-Circuit Debugger/Programmer
Производитель: China MaiLand
Модель: PICkit 3
Наличие: 99
Цена: 2700 р.
Количество:  
   - или -   

Microchip’s PICkit 3 In-Circuit Debugger/Programmer uses in-circuit debugging logic incorporated into each chip with Flash memory to provide a low-cost hardware debugger and programmer. In-circuit debugging offers these benefits:

    Low cost
    Minimum of additional hardware needed for debug
    Expensive sockets or adapters are not required

The PICkit 3 can now also reprogram any PIC microcontroller with a simple push of a button: Find out more about Programmer-To-Go function

Note: The PICkit 3 In-Circuit Debugger/Programmer is NOT a production programmer. It should be used for development purposes only.

The MPLAB PICkit 3 allows debugging and programming of PIC® and dsPIC® Flash microcontrollers at a most affordable price point using the powerful graphical user interface of the MPLAB X Integrated Development Environment (IDE). The MPLAB PICkit 3 is connected to the design engineer's PC using a full speed USB interface and can be connected to the target via an Microchip debug (RJ-11) connector (compatible with MPLAB ICD 2, MPLAB ICD 3 and MPLAB REAL ICE). The connector uses two device I/O pins and the reset line to implement in-circuit debugging and In-Circuit Serial Programming™.

If you need older software for programming with your PICkit 3, please visit our archives.

Header Information

Some 8-, 14- and 18-pin devices use small header boards with a special MCU for debugging. This special MCU has extra pins for PICkit 3 communication and therefore allows the use of all pins on the part for the application. The header board is not used or needed for programming. However, when debugging these devices the header must be used. See the "Header Specification" document below.

    Features
    Package Contents
    Host System Requirements
    Related Tools

        USB (Full speed 12 Mbits/s interface to host PC)
        Real-time execution
        MPLAB IDE compatible (free copy included)
        Built-in over-voltage/short circuit monitor
        Firmware upgradeable from PC/web download
        Totally enclosed
        Supports low voltage to 2.0 volts (2.0v to 6.0v range)
        Diagnostic LEDs (power, busy, error)
        Read/write program and data memory of microcontroller
        Erase of program memory space with verification
        Freeze-peripherals at breakpoint
        Program up to 512K byte flash with the Programmer-to-Go
        Header Information

    Some 8-, 14- and 18-pin devices use small header boards with a special MCU for debugging. This special MCU has extra pins for PICkit 3 communication and therefore allows the use of all pins on the part for the application. The header board is not used or needed for programming. However, when debugging these devices the header must be used. See the "Header Specification" document below.

117519, Москва, Кировоградская, 15 .
м. "Пражская", ТЦ "Электронный Рай", павильон 1Б-48.
Время работы павильона: с 11:00 до 19:00 без выходных дней.
Инженер по ремонту бывает - понедельник, четверг - с 11:00 до 17:00.
Есть вопросы? Звоните. Телефоны:  +7(926) 235-96-03

E-mail: support@azlina.ru

 New tipe


Просмотреть увеличенную карту

Написать отзыв

Ваше Имя:


Ваш отзыв: Внимание: HTML не поддерживается! Используйте обычный текст.

Оценка: Плохо            Хорошо

Введите код, указанный на картинке:



xx © 2018